JOTUN TANKGUARD 412 PDF
Tankguard is a solvent-free, two-pack epoxy tank coating. This product is e.g crude oil – please contact Jotun for specific recommendations. Film thickness . Jotun Tankguard is a two pack solvent free polyamine cured epoxy coating. It is a general purpose tank lining with good chemical resistance. Tankguard can also be used for corrosion protection for the internal lining of steel storage tanks and for friction reduction in gas pipes – please contact Jotun.
|Published (Last):||3 September 2013|
|PDF File Size:||16.53 Mb|
|ePub File Size:||18.66 Mb|
|Price:||Free* [*Free Regsitration Required]|
Low trade prices Our best trade prices on everything!
Safety Data Sheet Activator. Film thickness and spreading rate. Jotun Tankguard can be used as a coating for potable water, grey water and crude oil tanks. The content of this website is our best recommendation and is not advice. B curing agent in a 5 litre container.
Film thickness and spreading rate As tank coating. Jotafloor Non Slip Aggregate. Also available on special order in litre IBC containers, please contact Jotun for further information Health takguard safety Please observe the precautionary notices displayed on the container.
Two component polyamine cured novolac epoxy coating – specially designed tank coating with excellent chemical resistance. It can also be used for corrosion protection for the internal lining of steel storage tanks and for friction reduction in gas pipes – please contact us for specific recommendations.
Be aware that higher storage temperature will shorten the pot life after mixing. Not sure which is the best product? The question has been correctly sent. Please contact Jotun’s local technical service team for further information, or refer to the Application guide.
Jotun Tankguard – East Midlands Paint Supplies
Please observe the precautionary notices displayed on the container. Tankguard is a solvent-free, two-pack epoxy tank coating. Please select an option from the list above.
A base to be mixed thoroughly with 1 part TankguardComp. Jotun Paints Description Tankguard is a two pack, solvent free, polyamine cured, epoxy coating, designed as a general purpose tank lining with good chemical resistance. Brush Recommended for stripe coating and small areas, care must be taken to achieve the specified dry film thickness.
Jotun Tankguard 412 Paints
For stripe coating, however, a lower paint temperature may be favourable, in order to get a sufficient pot life. The coating may tangkuard used on other substrates. Handling Handle with care. Dry to recoat, minimum Dry to recoat, maximum 2.
Evaporation will only concentrate remaining contaminants. Other surfaces The coating may be used on other substrates. Elmbridge Menu 0 Your shopping basket is empty.
I would like to hear about offers and services: Favourites Account 0 Basket Your shopping basket is empty. Preferred time for Callback 9am – 11am 11am – 1pm 1pm – 3pm 3pm – 5pm.
Alternatively, one of the following procedures may be employed: Good ventilation is usually required in confined areas to ensure proper drying.
Drying times are generally related to air circulation, temperature, film thickness and number of coats, and will be affected correspondingly.
As a tank coating: The minimum purchase order quantity for the product is 1. Should, however, air bubbles in the paint be a problem a coarse filter may be employed. Two component polyaminde cured epoxy coating.
Guiding data airless spray Pressure at nozzle 25 – 35 MPa – p. General purpose tank lining with good chemical resistance. When used for pipe coating at raised temperature it is recommended to aim for an average DFT between 80 – microns Tan,guard above the profile of the steel. Additional certificates and approvals may be available on request.
Do you consent to us storing your information for that purpose? Fast drying, surface tolerant, hard wearing, high solids product. The figures stated above are approximate. Eyes should be well flushed with water and medical attention sought immediately.
Jotun Tankguard is recommended as an internal lining for offshore, onshore and buried tanks and pipes. Manually scrubbing the tank with warm water and an alkaline detergent. On completion of the washing the tank shall be emptied of water by pumping. The letter of approval from the Norwegian Institute of Public Health specifies several possible procedures.
This product is no longer in stock Jotjn. The surface should be assessed and treated in accordance with ISO Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets.